Conforme à VDI 6022

DID614

Active chilled beam with four-way air discharge and horizontal heat exchanger, suitable for grid ceilings with grid size 600 or 625

Active chilled beam for heating and cooling, with 2-pipe or 4-pipe heat exchanger, for integration with various ceiling systems.
  • Preferably for room heights up to 4.20 m
  • High heating and cooling capacity with a low conditioned primary air volume flow rate and low sound power level
  • High comfort levels due to low airflow velocity in the occupied zone
  • Five nozzle variants, including a variant with adjustable twin nozzles, to optimise induction
  • Removable front, fixed with magnets

Optional equipment and accessories
  • Regulating equipment

APPLICATION

Application

  • Active chilled beams of Type DID614 for the integration into various ceiling systems, preferably for room heights up to 4,20 m
  • Particularly suitable for grid ceilings with grid size 600 or 625
  • 2-pipe or 4-pipe heat exchangers enable good comfort levels with a low conditioned primary air volume flow rate
  • Energy-efficient solution since water is used as a medium for heating and cooling
  • Adjustable JetSplit air control blades (optional) allow for the manual adjustment of the four-way air discharge
  • Large volume flow rate range due  to the adjustable twin nozzles (optional)

Special features

  • Four-way air discharge
  • Horizontal heat exchanger as 2-pipe or 4-pipe system
  • Water connection, Ø12 mm Cu pipe or coupling with 1/2" external thread or 1/2" internal thread
  • Optional twin nozzles, adjustable, for a large volume flow rate range

DESCRIPTION

Construction

  • Powder-coated RAL 9003 - gloss 30
  • SL: Special finish

Attachments
  • Regulating equipment

Usefuls additions

  • Valves, regulators and actuators

Construction features

  • Spigot is suitable for circular ducts to EN 1506 or EN 13180
  • Removable front, fixed with magnets, secured with safety cables
  • 4 suspension points for on-site installation
  • Five nozzle variants to optimise induction

Materials and surfaces

  • Casing, spigot, nozzle plate and front is made of galvanised sheet steel
  • Heat exchanger with copper tubes and aluminium fins
  • Exposed surfaces are powder-coated with RAL 9003 - gloss 30
  • JetSplit air control blades made of polypropylene, UL 94, flame retardant (V0)

Technical information

  • Function
  • Technical data
  • Specification text
  • ORDER CODE

JetSplit air control blades

If a high cooling capacity is required in a very small space with active chilled beams, optional JetSplit air control blades allow for adjusting the air discharge direction such that the acceptable air velocity in the occupied zone is not exceeded. The airflow of each active chilled beam is spread and discharged according to the room geometry. if the use of a room changes, the air distribution can be optimised by adjusting the JetSplit air control blades accordingly.

  • It is possible to adjust several sets of JetSplit air control blades together
  • For fine adjustment, the sets of JetSplit air control blades can be disconnected from each other
  • To adjust a set of JetSplit air control blades, use both hands to move the two outer blades of the set as required
  • Maximum possible adjustment is 45° to the right or left in steps of 15°
  • The JetSplit air control blades are factory set to straight air discharge


If the air discharge is not straight, the water-side capacity will be slightly affected. JetSplit air control blades set at 45° may cause a loss of up to 5%.

Active chilled beams of Type DID614, with fourway air discharge and high thermal output, for air-water systems. For installation flush with the ceiling, preferably in rooms with a height up to 4.20 m. The units consist of a casing with suspension points, a spigot, non-combustible nozzles, and a horizontal heat exchanger. Five nozzle variants to optimise induction.
 
Special features
  • Four-way air discharge
  • Horizontal heat exchanger as 2-pipe or 4-pipe system
  • Water connection, Ø12 mm Cu pipe or coupling with 1/2" external thread or 1/2" internal thread
  • Adjustable nozzle configuration for a large volume flow rate range

Materials and surfaces
  • Casing, spigot, nozzle plate, and front is made of sheet steel
  • Heat exchanger with copper tubes and aluminium fins
  • Exposed surfaces are powder coated with RAL 9003 - gloss 30
  • JetSplit air control blades made of polypropylene, UL 94, flame retardant (V0)

Construction
  • Powder coated RAL 9003 - gloss 30
  • SL: Special finish

Technical data
  • Nominal length: 600, 1200 mm
  • Length: 593, 598, 618, 623 mm, or 1193, 1198, 1243, 1248 mm
  • Height: 230/245 mm
  • Widht: 593, 518, 618, 623 mm
  • Primary air spigot, diameter: 125/160 mm
  • Max. operating pressure: 10 bar
  • Max. operating temperature: 75 °C

Downloads

product information

certificates

production {"X-Frame-Options"=>"SAMEORIGIN", "X-XSS-Protection"=>"1; mode=block", "X-Content-Type-Options"=>"nosniff", "X-Download-Options"=>"noopen", "X-Permitted-Cross-Domain-Policies"=>"none", "Referrer-Policy"=>"strict-origin-when-cross-origin", "Content-Security-Policy"=>"frame-ancestors 'self' https://api.scrivito.com https://punchoutcommerce.com https://www.trox.de https://trox-extern.com https://psp40.onventis.com https://psp22.onventis.com https://trox4u.troxgroup.com", "Strict-Transport-Security"=>"max-age=31536000; includeSubDomains", "Content-Type"=>"text/html; charset=utf-8"}

Share page

Recommend this page

Recommend this page by sending a link by mail.

Fields marked with an (*) are required fields.

Share page

Thank you for your recommendation!

Your recommendation has been sent and should arrive shortly.

Contact

We are here for you

Please specify your message and type of request
Tel.: +49 (0)2845 / 202-0 | Fax: +49 (0)2845/202-265

Fields marked with an (*) are required fields.

Contact

Thank you for your message!

Your message is send and will be processed shortly.
Our department for Service-Requests will contact you asap.
For general question regarding products or services you can also call:
Tel.: +49 (0)2845 / 202-0 | Fax: +49 (0)2845/202-265

Contact

We are here for you

Please specify your message and type of request
Tel.: +49 (0)2845 / 202-0 | Fax: +49 (0)2845/202-265

Attachment (max. 10MB)

Fields marked with an (*) are required fields.

Contact

Thank you for your message!

Your message is send and will be processed shortly.
Our department for Service-Requests will contact you asap.
For general question regarding products or services you can also call:
Tel.: +49 (0)2845 / 202-0 | Fax: +49 (0)2845/202-265